[FFmpeg-devel] [PATCH v3] lavc/vaapi_encode: Enable block level bitrate control
Xiang, Haihao
haihao.xiang at intel.com
Mon Mar 18 08:05:39 EET 2024
On Vr, 2024-03-15 at 02:46 +0000, Xiang, Haihao wrote:
> On Vr, 2024-03-08 at 16:45 +0800, fei.w.wang-at-intel.com at ffmpeg.org wrote:
> > From: Fei Wang <fei.w.wang at intel.com>
> >
> > Signed-off-by: Fei Wang <fei.w.wang at intel.com>
> > ---
> > doc/encoders.texi | 4 ++++
> > libavcodec/vaapi_encode.c | 13 ++++++++++++-
> > libavcodec/vaapi_encode.h | 9 ++++++++-
> > 3 files changed, 24 insertions(+), 2 deletions(-)
> >
> > diff --git a/doc/encoders.texi b/doc/encoders.texi
> > index 5f7864770e..7c223ed74c 100644
> > --- a/doc/encoders.texi
> > +++ b/doc/encoders.texi
> > @@ -4089,6 +4089,10 @@ Quality-defined variable-bitrate.
> > Average variable bitrate.
> > @end table
> >
> > + at item blbrc
> > +Enable block level rate control, which assigns different bitrate block by
> > block.
> > +Invalid for CQP mode.
> > +
> > @end table
> >
> > Each encoder also has its own specific options:
> > diff --git a/libavcodec/vaapi_encode.c b/libavcodec/vaapi_encode.c
> > index 808b79c0c7..940f0678a5 100644
> > --- a/libavcodec/vaapi_encode.c
> > +++ b/libavcodec/vaapi_encode.c
> > @@ -1805,6 +1805,11 @@ static av_cold int
> > vaapi_encode_init_rate_control(AVCodecContext *avctx)
> > int i, first = 1, res;
> >
> > supported_va_rc_modes = rc_attr.value;
> > + if (ctx->blbrc && !(supported_va_rc_modes & VA_RC_MB)) {
> > + ctx->blbrc = 0;
> > + av_log(avctx, AV_LOG_WARNING, "Driver does not support
> > BLBRC.\n");
> > + }
> > +
> > for (i = 0; i < FF_ARRAY_ELEMS(vaapi_encode_rc_modes); i++) {
> > rc_mode = &vaapi_encode_rc_modes[i];
> > if (supported_va_rc_modes & rc_mode->va_mode) {
> > @@ -2016,13 +2021,18 @@ rc_mode_found:
> > ctx->va_bit_rate = rc_bits_per_second;
> >
> > av_log(avctx, AV_LOG_VERBOSE, "RC mode: %s.\n", rc_mode->name);
> > +
> > + if (ctx->blbrc && ctx->va_rc_mode == VA_RC_CQP)
> > + ctx->blbrc = 0;
> > + av_log(avctx, AV_LOG_VERBOSE, "Block Level bitrate control: %s.\n",
> > ctx-
> > > blbrc ? "ON" : "OFF");
> > +
> > if (rc_attr.value == VA_ATTRIB_NOT_SUPPORTED) {
> > // This driver does not want the RC mode attribute to be set.
> > } else {
> > ctx->config_attributes[ctx->nb_config_attributes++] =
> > (VAConfigAttrib) {
> > .type = VAConfigAttribRateControl,
> > - .value = ctx->va_rc_mode,
> > + .value = ctx->blbrc ? ctx->va_rc_mode | VA_RC_MB : ctx-
> > > va_rc_mode,
> > };
> > }
> >
> > @@ -2051,6 +2061,7 @@ rc_mode_found:
> > #if VA_CHECK_VERSION(1, 1, 0)
> > .ICQ_quality_factor = av_clip(rc_quality, 1, 51),
> > .max_qp = (avctx->qmax > 0 ? avctx->qmax : 0),
> > + .rc_flags.bits.mb_rate_control = ctx->blbrc ? 1 : 2,
> > #endif
> > #if VA_CHECK_VERSION(1, 3, 0)
> > .quality_factor = rc_quality,
> > diff --git a/libavcodec/vaapi_encode.h b/libavcodec/vaapi_encode.h
> > index 6964055b93..0eed9691ca 100644
> > --- a/libavcodec/vaapi_encode.h
> > +++ b/libavcodec/vaapi_encode.h
> > @@ -216,6 +216,9 @@ typedef struct VAAPIEncodeContext {
> > // available modes).
> > int explicit_rc_mode;
> >
> > + // Block Level based bitrate control.
> > + int blbrc;
> > +
> > // Explicitly-set QP, for use with the "qp" options.
> > // (Forces CQP mode when set, overriding everything else.)
> > int explicit_qp;
> > @@ -538,7 +541,11 @@ int ff_vaapi_encode_close(AVCodecContext *avctx);
> > VAAPI_ENCODE_RC_MODE(VBR, "Variable-bitrate"), \
> > VAAPI_ENCODE_RC_MODE(ICQ, "Intelligent constant-quality"), \
> > VAAPI_ENCODE_RC_MODE(QVBR, "Quality-defined variable-bitrate"), \
> > - VAAPI_ENCODE_RC_MODE(AVBR, "Average variable-bitrate")
> > + VAAPI_ENCODE_RC_MODE(AVBR, "Average variable-bitrate"), \
> > + { "blbrc", \
> > + "Block level based bitrate control",\
> > + OFFSET(common.blbrc), AV_OPT_TYPE_BOOL, \
> > + { .i64 = 0 }, 0, 1, FLAGS }
> >
> >
> > #endif /* AVCODEC_VAAPI_ENCODE_H */
>
> LGTM, I will push this patch if there is no objection.
Pushed.
- Haihao
More information about the ffmpeg-devel
mailing list